LOGO-HomeKit-Bridge

A HomeKit Bridge for Siemens LOGO!s.

Setup Code: 231-90-645

Setup ID: LHB1

Requires components:

ESP32-S2 board (with 16MB Flash & 8MB PSRAM)
Ethernet interface with WIZnet W5500
SD card adapter
Mac or PC with EspTool installed

Example configuration:

Infos:

Reset bridge after pairing, to announce all Accessories!
Limits: 10 LOGOs each with 30 Accessories and 10 Sensors
HomeKit name length limit is 15 characters!
The connection on the underside of the MKR ETH Shield from the ETH_INT pad to pin 3 must be made by yourself! Without it, the Ethernet connection will not work!
The mac address is the ethernet mac address from the ESP32-S2 chip and not that from the sticker on the shield.
In the serial connection you can see the HomeKit configuration QR code. And lots of other useful information and error messages.

TODO:

Modify the PCB to add a 24V input and DIN rail support.
Add Alexa support.

Buttons & LEDs:

BOOT - short (3sec) press - Reset HomeKit Data
BOOT - long (10sec) press - Reset to Factory
SW1 - holding at start up - SD card will be partitioned and formatted in case when mounting fails
LED 1 (green) - on at start up to indicate SD card reading
LED 2 (orange) - on at start up to indicate SD card formating on mount fail
LED 3 (red) - Error
LED 4 (blue) - on at start up

Webserver:

Is activated by specifying a port number in the config. e.g. 8080
Information about the current configuration on: "/"
Config upload on: "/config"
The file name on the PC does not matter, only the content is uploaded.
The last old config on the SD card is not overwritten, just renamed to "old_n.cfg".

Type of Accessory:

Switch
Lightbulb
Blind
Window
Garage Door
Thermostat
Irrigation System
Valve
Fan
Filter Maintenance

Type of Sensor Accessory:

Light Sensor
Motion Sensor
Contact Sensor
Smoke Sensor
Temperature Sensor
Humidity Sensor
Carbon Dioxide Sensor
Air Quality Sensor
Leak Sensor

Flash:

$ esptool.py -p [USB_device] -b 460800 --before no_reset --after no_reset --chip esp32s2 write_flash --flash_mode dio --flash_size detect --flash_freq 80m 0x1000 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin 0x16000 build/ota_data_initial.bin 0x20000 build/ethernet_bridge.bin

LOGO-HomeKit-Bridge Main Configuration Parameters

Name	Value	Required	Notes
`http_port`	8080	no	Info & Update Webserver Port (greater than 0 and not 80).
`update_interval`	5000	no	Update Interval (in MS) for all Accessories and Sensors, default is: 5000.
`debug_level`	0	no	Debug Level for Serial Output. 0 - Error, 1 - Warning, 2 - Info, default is: 0.
`mb_port`	502	yes	Must be set to the Modbus Port of your LOGO! PLCs.
`plcs`	[...]	yes	A array of all your LOGO! PLCs.

PLC Configuration

Name	Value	Required	Notes
`name`	"Logo 1"	yes	Name of your LOGO! PLC.
`ip`	"192.168.1.100"	yes	Must be set to the IP of your LOGO! PLC.
`items`	[...]	yes	A array of all accessorys and or sensors from this LOGO! PLC.

Main Item Configuration

Name	Value	Required	Option for	Notes
`name`	(custom)	yes	all	Name of accessory that will appear in homekit app.
`type`	"switch" or ...	yes	all	Type of Accessory or Sensor
`pushButton`	0 or 1	no	all	If e.g. the network input in the LOGO! a hardware button on the LOGO! simulated, default is: 1.

Switch Configuration

Name	Value	Required	Option for	Notes
`switchGet`	"Q1"	yes*	"switch"	Switch Get - Qn, Mn or Vn.n
`switchSetOn`	"V1.0"	yes*	"switch"	Switch Set On - Mn or Vn.n
`switchSetOff`	"V1.1"	yes*	"switch"	Switch Set Off - Mn or Vn.n

{
    "name": "Item-1",
    "type": "switch",
    "switchGet": "Q1",
    "switchSetOn": "V1.0",
    "switchSetOff": "V1.1"
}

Lightbulb Configuration

Name	Value	Required	Option for	Notes
`lightbulbGet`	"Q4"	yes*	"lightbulb"	Lightbulb Get - Qn, Mn or Vn.n
`lightbulbSetOn`	"V2.0"	yes*	"lightbulb"	Lightbulb Set On - Mn or Vn.n
`lightbulbSetOff`	"V2.1"	yes*	"lightbulb"	Lightbulb Set Off - Mn or Vn.n
`lightbulbSetBrightness`	"VW20"	no*	"lightbulb"	Lightbulb Set Brightness - AMn or VWn
`lightbulbGetBrightness`	"VW22"	no*	"lightbulb"	Lightbulb Get Brightness - AMn or VWn

{
    "name": "Item-5",
    "type": "lightbulb",
    "lightbulbGet": "Q4",
    "lightbulbSetOn": "V2.0",
    "lightbulbSetOff": "V2.1",
    "lightbulbSetBrightness": "VW20",
    "lightbulbGetBrightness": "VW22"
}

Blind Configuration

Name	Value	Required	Option for	Notes
`blindSetTargetPos`	"VW26"	yes*	"blind"	Blind Set Target Pos - AMn or VWn
`blindGetTargetPos`	"VW28"	yes*	"blind"	Blind Get Target Pos - AMn or VWn
`blindGetPos`	"VW28"	yes*	"blind"	Blind Get Pos - AMn or VWn
`blindGetState`	"VW30"	yes*	"blind"	Blind Get State - AMn or VWn
`blindConvertValue`	0 or 1	no*	"blind"	Convert LOGO! values in to HomeKit values, default is: 1.

{
    "name": "Item-6",
    "type": "blind",
    "blindConvertValue": 1,
    "blindSetTargetPos": "VW26",
    "blindGetTargetPos": "VW28",
    "blindGetPos": "VW28",
    "blindGetState": "VW30"
}

Window Configuration

Name	Value	Required	Option for	Notes
`windowSetTargetPos`	"VW32"	yes*	"window"	Window Set Target Pos - AMn or VWn
`windowGetTargetPos`	"VW34"	yes*	"window"	Window Get Target Pos - AMn or VWn
`windowGetPos`	"VW34"	yes*	"window"	Window Get Pos - AMn or VWn
`windowSetState`	"VW36"	yes*	"window"	Window Get State - AMn or VWn
`windowConvertValue`	0 or 1	no*	"window"	Convert LOGO! values in to HomeKit values, default is: 1.

{
    "name": "Item-7",
    "type": "window",
    "windowConvertValue": 1,
    "windowSetTargetPos": "VW32",
    "windowGetTargetPos": "VW34",
    "windowGetPos": "VW34",
    "windowGetState": "VW36"
}

Garage Door Configuration

Name	Value	Required	Option for	Notes
`garagedoorGetState`	"VW40"	yes*	"garagedoor"	Garagedoor Get State - AMn or VWn (0 = Open; 1 = Closed; 2 = Opening; 3 = Closing; 4 = Stopped)
`garagedoorGetTargetState`	"VW40"	yes*	"garagedoor"	Garagedoor Get Target State - AMn or VWn (0 = Open; 1 = Closed)
`garagedoorSetTargetState`	"VW38"	yes*	"garagedoor"	Garagedoor Set Target State - AMn or VWn (0 = Open; 1 = Closed)
`garagedoorObstruction`	"V3.0"	no*	"garagedoor"	Garagedoor Obstruction Detected - Mn or Vn.n

{
    "name": "Item-8",
    "type": "garagedoor",
    "garagedoorGetState": "VW40",
    "garagedoorGetTargetState": "VW40",
    "garagedoorSetTargetState": "VW38",
    "garagedoorObstruction": "V3.0"
}

Thermostat Configuration

Name	Value	Required	Option for	Notes
`thermostatGetHCState`	"VW42"	yes*	"thermostat"	Thermostat Get Heating Cooling State - AMn or VWn
`thermostatGetTargetHCState`	"VW44"	yes*	"thermostat"	Thermostat Get Target Heating Cooling State - AMn or VWn
`thermostatSetTargetHCState`	"VW46"	yes*	"thermostat"	Thermostat Set Target Heating Cooling State - AMn or VWn
`thermostatGetTemp`	"VW48"	yes*	"thermostat"	Thermostat Get Temperature - AMn or VWn - Current Temperature in °C (0°C - 100°C!!)
`thermostatGetTargetTemp`	"VW50"	yes*	"thermostat"	Thermostat Get Target Temperature - AMn or VWn - Current Temperature in °C (10°C - 38°C!!)
`thermostatSetTargetTemp`	"VW52"	yes*	"thermostat"	Thermostat Set Target Temperature - AMn or VWn
`thermostatTempDisplayUnits`	0 or 1	yes*	"thermostat"	Temperature Display Units - Celsius = 0; Fahrenheit = 1;
`thermostatConvertValue`	0 or 1	no*	"thermostat"	Convert Int in Float, default is: 0. (235 / 10 == 23.5°C)

{
    "name": "Item-9",
    "type": "thermostat",
    "thermostatGetHCState": "VW42",
    "thermostatGetTargetHCState": "VW44",
    "thermostatSetTargetHCState": "VW46",
    "thermostatGetTemp": "VW48",
    "thermostatGetTargetTemp": "VW50",
    "thermostatSetTargetTemp": "VW52",
    "thermostatTempDisplayUnits": 0,
    "thermostatConvertValue": 1
}

Irrigation System Configuration

Name	Value	Required	Option for	Notes
`irrigationSystemGetActive`	"V4.0"	yes*	"irrigationSystem"	Irrigation System Get Active - Mn or Vn.n
`irrigationSystemSetActiveOn`	"V4.1"	yes*	"irrigationSystem"	Irrigation System Set Active to On - Mn or Vn.n
`irrigationSystemSetActiveOff`	"V4.2"	yes*	"irrigationSystem"	Irrigation System Set Active to Off - Mn or Vn.n
`irrigationSystemGetProgramMode`	"VW54"	yes*	"irrigationSystem"	Irrigation System Get Program Mode - AMn or VWn - (0 - No Program scheduled; 1 - Program scheduled; 2 - Program scheduled manual Mode)
`irrigationSystemGetInUse`	"V4.3"	yes*	"irrigationSystem"	Irrigation System Get In Use - Mn or Vn.n

{
    "name": "Item-10",
    "type": "irrigationSystem",
    "irrigationSystemGetActive": "V4.0",
    "irrigationSystemSetActiveOn": "V4.1",
    "irrigationSystemSetActiveOff": "V4.2",
    "irrigationSystemGetProgramMode": "VW54",
    "irrigationSystemGetInUse": "V4.3"
}

Valve Configuration

Name	Value	Required	Option for	Notes
`valveGetActive`	"V5.0"	yes*	"valve"	Valve Get Active - Mn or Vn.n
`valveSetActiveOn`	"V5.1"	yes*	"valve"	Valve Set Active to On - Mn or Vn.n
`valveSetActiveOff`	"V5.2"	yes*	"valve"	Valve Set Active to Off - Mn or Vn.n
`valveGetInUse`	"V5.3"	yes*	"valve"	Valve Get In Use - Mn or Vn.n
`valveType`	0	yes*	"valve"	Valve Type - Generic Valve = 0, Irrigation = 1, Shower Head = 2, Water Faucet = 3,
`valveSetDuration`	"VW56"	no*	"valve"	Valve Set Duration - AMn or VWn - Value in Seconds (0 - 3600 sec)
`valveGetDuration`	"VW56"	no*	"valve"	Valve Get Duration - AMn or VWn - Value in Seconds (0 - 3600 sec)
`valveGetRemainingDuration`	"VW58"	no*	"valve"	Valve Get Remaining Duration - AMn or VWn - Value in Seconds (0 - 3600 sec)

{
    "name": "Item-11",
    "type": "valve",
    "valveGetActive": "V5.0",
    "valveSetActiveOn": "V5.1",
    "valveSetActiveOff": "V5.2",
    "valveGetInUse": "V5.3",
    "valveType": 1,
    "valveSetDuration": "VW56",
    "valveGetDuration": "VW56",
    "valveGetRemainingDuration": "VW58"
}

Fan Configuration

Name	Value	Required	Option for	Notes
`fanGetActive`	"V6.0"	yes*	"fan"	Fan Get Active - Mn or Vn.n
`fanSetActiveOn`	"V6.1"	yes*	"fan"	Fan Set Active to On - Mn or Vn.n
`fanSetActiveOff`	"V6.2"	yes*	"fan"	Fan Set Active to Off - Mn or Vn.n
`fanGetRotationDirection`	"V6.3"	no*	"fan"	Fan Get Rotation Direction - Mn or Vn.n
`fanSetRotationDirectionCW`	"V6.4"	no*	"fan"	Fan Set Rotation Direction to Clockwise - Mn or Vn.n
`fanSetRotationDirectionCCW`	"V6.5"	no*	"fan"	Fan Set Rotation Direction to Counter Clockwise - Mn or Vn.n
`fanGetRotationSpeed`	"VW60"	no*	"fan"	Fan Get Rotation Speed - AMn or VWn
`fanSetRotationSpeed`	"VW62"	no*	"fan"	Fan Set Rotation Speed - AMn or VWn

{
    "name": "Item-12",
    "type": "fan",
    "fanGetActive": "V6.0",
    "fanSetActiveOn": "V6.1",
    "fanSetActiveOff": "V6.2",
    "fanGetRotationDirection": "V6.3",
    "fanSetRotationDirectionCW": "V6.4",
    "fanSetRotationDirectionCCW": "V6.5",
    "fanGetRotationSpeed": "VW60",
    "fanSetRotationSpeed": "VW62"
}

Filter Maintenance Configuration

🚧 In HomeKit Accessory Protocol Specification available but currently not supported by the Home-App!

Name	Value	Required	Option for	Notes
`filterChangeIndication`	"V7.0"	yes*	"filterMaintenance"	Filter Maintenance Get Filter Change Indication - Mn or Vn.n
`filterLifeLevel`	"VW64"	no*	"filterMaintenance"	Filter Maintenance Get Filter Life Level - AMn or VWn
`filterResetFilterIndication`	"V7.1"	no*	"filterMaintenance"	Filter Maintenance Set Reset Filter Indication - Mn or Vn.n

{
    "name": "Item-13",
    "type": "filterMaintenance",
    "filterChangeIndication": "V7.0",
    "filterLifeLevel": "VW64",
    "filterResetFilterIndication": "V7.1"
}

Light Sensor Configuration

Name	Value	Required	Option for	Notes
`light`	"VW66"	yes*	"lightSensor"	Light Sensor for Current Ambient Light Level in Lux

{
    "name": "Sensor-1",
    "type": "lightSensor",
    "light": "VW66"
}

Motion Sensor Accessory Configuration

Name	Value	Required	Option for	Notes
`motion`	"V8.0"	yes*	"motionSensor"	Motion Sensor

{
    "name": "Sensor-2",
    "type": "motionSensor",
    "motion": "V8.0"
}

Contact Sensor Configuration

Name	Value	Required	Option for	Notes
`contact`	"V8.1"	yes*	"contactSensor"	Contact Sensor

{
    "name": "Sensor-3",
    "type": "contactSensor",
    "contact": "V8.1"
}

Smoke Sensor Configuration

Name	Value	Required	Option for	Notes
`smoke`	"V8.2"	yes*	"smokeSensor"	Smoke Sensor

{
    "name": "Sensor-4",
    "type": "smokeSensor",
    "smoke": "V8.2"
}

Temperature Sensor Configuration

Name	Value	Required	Option for	Notes
`temperature`	"VW68"	yes*	"temperatureSensor"	Temperature Sensor for Current Temperature in °C (0°C - 100°C!!)
`convertValue`	0 or 1	no*	"temperatureSensor"	Convert Int in Float, default is: 0. (235 / 10 == 23.5°C)

{
    "name": "Sensor-5",
    "type": "temperatureSensor",
    "convertValue": 1,
    "temperature": "VW68"
}

Humidity Sensor Configuration

Name	Value	Required	Option for	Notes
`humidity`	"VW70"	yes*	"humiditySensor"	Humidity Sensor for Current Relative Humidity in %
`convertValue`	0 or 1	no*	"humiditySensor"	Convert Int in Float, default is: 0. (456 / 10 == 45.6%rH => 46%rH in Home App)

{
    "name": "Sensor-6",
    "type": "humiditySensor",
    "convertValue": 1,
    "humidity": "VW70"
}

Carbon Dioxide Sensor Configuration

Name	Value	Required	Option for	Notes
`carbonDioxide`	"V9.0"	yes*	"carbonDioxideSensor"	Carbon Dioxide
`carbonDioxideLevel`	"VW72"	no*	"carbonDioxideSensor"	Carbon Dioxide Level in ppm
`carbonDioxidePeakLevel`	"VW74"	no*	"carbonDioxideSensor"	Carbon Dioxide Peak Level in ppm

{
    "name": "Sensor-7",
    "type": "carbonDioxideSensor",
    "carbonDioxide": "V9.0",
    "carbonDioxideLevel": "VW72",
    "carbonDioxidePeakLevel": "VW74"
}

Air Quality Sensor Configuration

Name	Value	Required	Option for	Notes
`airQuality`	"VW76"	yes*	"airQualitySensor"	Air Quality (0 - 5)

0 - Unknown
1 - Excellent - CO2 < 800ppm (IDA 1)
2 - Good - CO2 = 800 - 1000ppm (IDA 2)
3 - Fair - CO2 = 1000 - 1400ppm (IDA 3)
4 - Inferior - CO2 = 1400 - 1800ppm (IDA 4)
5 - Poor - CO2 > 1800ppm

{
    "name": "Sensor-8",
    "type": "airQualitySensor",
    "airQuality": "VW76"
}

Leak Sensor Configuration

Name	Value	Required	Option for	Notes
`leak`	"V9.1"	yes*	"leakSensor"	Leak Sensor
`waterLevel`	"VW78"	no*	"leakSensor"	Water Level in %

{
    "name": "Sensor-9",
    "type": "leakSensor",
    "leak": "V9.1",
    "waterLevel": "VW78"
}

Example Configuration

bridge.cfg file on SD card. [JSON]

{
    "http_port": 8080,
    "update_interval": 1000,
    "debug_level": 2,
    "mb_port": 502,
    "plcs": [
        {
            "name": "Logo 1",
            "ip": "192.168.001.100",
            "items": [
                {
                    "name": "Item-1",
                    "type": "switch",
                    "pushButton": 1,
                    "switchGet": "Q1",
                    "switchSetOn": "V1.0",
                    "switchSetOff": "V1.1"
                },
                {
                    "name": "Item-2",
                    "type": "switch",
                    "switchGet": "Q2",
                    "switchSetOn": "V1.2",
                    "switchSetOff": "V1.3"
                },
                {
                    "name": "Item-3",
                    "type": "switch",
                    "switchGet": "Q3",
                    "switchSetOn": "V1.4",
                    "switchSetOff": "V1.5"
                },
                {
                    "name": "Item-4",
                    "type": "switch",
                    "switchGet": "M1",
                    "switchSetOn": "V1.6",
                    "switchSetOff": "V1.7"
                },
                {
                    "name": "Item-5",
                    "type": "lightbulb",
                    "lightbulbGet": "Q4",
                    "lightbulbSetOn": "V2.0",
                    "lightbulbSetOff": "V2.1",
                    "lightbulbSetBrightness": "VW20",
                    "lightbulbGetBrightness": "VW22"
                },
                {
                    "name": "Item-6",
                    "type": "blind",
                    "blindConvertValue": 1,
                    "blindSetTargetPos": "VW26",
                    "blindGetTargetPos": "VW28",
                    "blindGetPos": "VW28",
                    "blindGetState": "VW30"
                },
                {
                    "name": "Item-7",
                    "type": "window",
                    "windowConvertValue": 1,
                    "windowSetTargetPos": "VW32",
                    "windowGetTargetPos": "VW34",
                    "windowGetPos": "VW34",
                    "windowGetState": "VW36"
                },
                {
                    "name": "Item-8",
                    "type": "garagedoor",
                    "garagedoorGetState": "VW40",
                    "garagedoorGetTargetState": "VW40",
                    "garagedoorSetTargetState": "VW38",
                    "garagedoorObstruction": "V3.0"
                },
                {
                    "name": "Item-9",
                    "type": "thermostat",
                    "thermostatGetHCState": "VW42",
                    "thermostatGetTargetHCState": "VW44",
                    "thermostatSetTargetHCState": "VW46",
                    "thermostatGetTemp": "VW48",
                    "thermostatGetTargetTemp": "VW50",
                    "thermostatSetTargetTemp": "VW52",
                    "thermostatTempDisplayUnits": 0
                },
                {
                    "name": "Item-10",
                    "type": "irrigationSystem",
                    "irrigationSystemGetActive": "V4.0",
                    "irrigationSystemSetActiveOn": "V4.1",
                    "irrigationSystemSetActiveOff": "V4.2",
                    "irrigationSystemGetProgramMode": "VW54",
                    "irrigationSystemGetInUse": "V4.3"
                },
                {
                    "name": "Item-11",
                    "type": "valve",
                    "valveGetActive": "V5.0",
                    "valveSetActiveOn": "V5.1",
                    "valveSetActiveOff": "V5.2",
                    "valveGetInUse": "V5.3",
                    "valveType": 1,
                    "valveSetDuration": "VW56",
                    "valveGetDuration": "VW56",
                    "valveGetRemainingDuration": "VW58"
                },
                {
                    "name": "Item-12",
                    "type": "fan",
                    "fanGetActive": "V6.0",
                    "fanSetActiveOn": "V6.1",
                    "fanSetActiveOff": "V6.2",
                    "fanGetRotationDirection": "V6.3",
                    "fanSetRotationDirectionCW": "V6.4",
                    "fanSetRotationDirectionCCW": "V6.5",
                    "fanGetRotationSpeed": "VW60",
                    "fanSetRotationSpeed": "VW62"
                },
                {
                    "name": "Item-13",
                    "type": "filterMaintenance",
                    "filterChangeIndication": "V7.0",
                    "filterLifeLevel": "VW64",
                    "filterResetFilterIndication": "V7.1"
                },
                {
                    "name": "Sensor-1",
                    "type": "lightSensor",
                    "light": "VW66"
                },
                {
                    "name": "Sensor-2",
                    "type": "motionSensor",
                    "motion": "V8.0"
                },
                {
                    "name": "Sensor-3",
                    "type": "contactSensor",
                    "contact": "V8.1"
                },
                {
                    "name": "Sensor-4",
                    "type": "smokeSensor",
                    "smoke": "V8.2"
                },
                {
                    "name": "Sensor-5",
                    "type": "temperatureSensor",
                    "convertValue": 1,
                    "temperature": "VW68"
                },
                {
                    "name": "Sensor-6",
                    "type": "humiditySensor",
                    "humidity": "VW70"
                },
                {
                    "name": "Sensor-7",
                    "type": "carbonDioxideSensor",
                    "carbonDioxide": "V9.0",
                    "carbonDioxideLevel": "VW72",
                    "carbonDioxidePeakLevel": "VW74"
                },
                {
                    "name": "Sensor-8",
                    "type": "airQualitySensor",
                    "airQuality": "VW76"
                },
                {
                    "name": "Sensor-9",
                    "type": "leakSensor",
                    "leak": "V9.1",
                    "waterLevel": "VW78"
                }
            ]
        }
    ]
}

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

LOGO-HomeKit-Bridge

LOGO-HomeKit-Bridge Main Configuration Parameters

PLC Configuration

Main Item Configuration

Switch Configuration

Lightbulb Configuration

Blind Configuration

Window Configuration

Garage Door Configuration

Thermostat Configuration

Irrigation System Configuration

Valve Configuration

Fan Configuration

Filter Maintenance Configuration

Light Sensor Configuration

Motion Sensor Accessory Configuration

Contact Sensor Configuration

Smoke Sensor Configuration

Temperature Sensor Configuration

Humidity Sensor Configuration

Carbon Dioxide Sensor Configuration

Air Quality Sensor Configuration

Leak Sensor Configuration

Example Configuration

About

Uh oh!

Releases

Packages

Uh oh!

Contributors

Uh oh!

Languages

Name		Name	Last commit message	Last commit date
Latest commit History 32 Commits
Arduino-ModBus		Arduino-ModBus
Images		Images
LOGO		LOGO
PCB		PCB
.gitignore		.gitignore
README.md		README.md
bootloader.bin		bootloader.bin
bridge.cfg		bridge.cfg
ethernet_bridge.bin		ethernet_bridge.bin
ota_data_initial.bin		ota_data_initial.bin
partition-table.bin		partition-table.bin

tompie87/LOGO-HomeKit-Bridge

Folders and files

Latest commit

History

Repository files navigation

LOGO-HomeKit-Bridge

LOGO-HomeKit-Bridge Main Configuration Parameters

PLC Configuration

Main Item Configuration

Switch Configuration

Lightbulb Configuration

Blind Configuration

Window Configuration

Garage Door Configuration

Thermostat Configuration

Irrigation System Configuration

Valve Configuration

Fan Configuration

Filter Maintenance Configuration

Light Sensor Configuration

Motion Sensor Accessory Configuration

Contact Sensor Configuration

Smoke Sensor Configuration

Temperature Sensor Configuration

Humidity Sensor Configuration

Carbon Dioxide Sensor Configuration

Air Quality Sensor Configuration

Leak Sensor Configuration

Example Configuration

About

Resources

Uh oh!

Stars

Watchers

Forks

Releases

Packages 0

Uh oh!

Contributors

Uh oh!

Languages

Packages